I've been internet ordering for years
and this has been my best experience!
The order was acknowledged quickly by email and updated
with tracking information. Not only was my order delivered in record
time, you emailed saving me from ordering incorrectly and later helped me with the installation,
too. Thank you so much for the great service.
Check your email for an order response.
Orders are verified. Tracking information
will be sent at the time of shipment. So please check your
email after ordering for the first email and daily for further emails
with information about your order. Thank you!
EMAIL SALES@SCOOTERSUPPORT.COM FOR AVAILABILITY AND PURCHASE
EACH 5/16 DIAMETER X-10 OEM AXLE $12.95 WITH USA SHIPPING (Handling Added Later)
OEM 4.5 inch Long 3/8 Diameter Axle for Front Wheel $9.95
plus Shipping and Handling
3/8 axle diameter, 4.5 inch length. Common Hardware included that varies: 2 - Nuts, 2 -
1/2" Spacers, and 4 - washers. Fits 200 X 50 Front Wheels and many others.
OEM 5.5 inch Front Wheel Axle and Hardware $19.95
plus shipping/handling
Choice of 3/8 or 15/16 inch diameter axle in the 5.5 inch length for original X360 Scooter versions
1 or 2 and many other scooters. Common nuts and washers included. X-treme X-360 OEM parts.
EMAIL SALES@SCOOTERSUPPORT.COM FOR AVAILABILITY AND PURCHASE
Version #
EACH OEM X360 AXLE $22.95 WITH USA SHIPPING (Handling Added Later)
DOUBLE END AXLE with Nuts/Washers $11.95
Plus Shipping/Handling
Axle, double-ended, with nuts, and washers. 4.5, 4.7, 5.0, 5.5, 6.3, 6.5, 6.7, 8.8 in 3/8 inch (10mm) diameter. 5 and 5.7 inch for 5/16 (8mm) diameter.
Five axle spacers (various sizes): 84mm, 47mm, 20mm, 10mm and 5mm with Inner Diameter of 12.5mm, two Washers, and 2 Axle Adjusters for 3/8 diameter axles.
Brake Drum assembly fits
many scooters including some Vapor, X-treme, Rad2Go, where space allows. 80mm (3 1/8") Diameter across the round brake hub (Not Included - Order above).
Band Brake Drum Assy for 90mm Hub $16.95
Plus Shipping/Handling
Brake Lever - Left (with common
kill switch) and steel Cable $17.95
Plus Shipping/Handling
Universal Brake Lever with two wire harness and
66 inch steel Cable with 60 inch sleeve (connectors fit most application). Switch is open until
lever is pulled, making a connection to the control box to kill all
scooter operation.
Brake Lever, Common kill switch $8.95
Plus Shipping/Handling
Universal Left Brake Lever (connectors fit most
application). Switch is open until lever is pulled, making
connection to the control box and killing power to the
motor.
Brake Lever, Common kill switch $8.95
Plus Shipping/Handling
Universal Right Brake Lever (connectors fit most
application). Switch is open until lever is pulled, making
connection to the control box and killing power to the
motor.
Brake Lever, alternate electrical operation $9.95
Plus Shipping/Handling
Universal Brake Lever (connectors fit most
application). Switch is made until lever is pulled, OPENING the
connection in an application where power is broken to a control box
switch circuit to shut down the scooter operation.
EMAIL SALES@SCOOTERSUPPORT.COM FOR AVAILABILITY AND PURCHASE
EACH REAR ROTOR $25.95 WITH USA SHIPPING (Handling Added Later)
REAR ROTOR FOR
DISK BRAKE $21.95
Plus Shipping and Handling
Disc brake rotor for mid-size pocket bikes including "cateye" style bikes and many other vehicles. Specifications: Inner Diameter: 37mm; Outer Diameter: 160mm; Bolt pattern: 6 bolts, 48mm hole spacing across the diameter; Thickness: 3mm
EMAIL SALES@SCOOTERSUPPORT.COM FOR AVAILABILITY AND PURCHASE
EACH FRONT ROTOR $25.95 WITH USA SHIPPING (Handling Added Later)
DISK BRAKE CALIPER $15.95
Plus Shipping and Handling
Disc Brake Caliper for most pocket bikes, mini choppers and scooters with non-hydraulic brakes. This is the most common type of disc brake caliper we sell for mini-vehicles! Bolt Hole Spacing: 51mm. Includes round tip brake pads.
EMAIL SALES@SCOOTERSUPPORT.COM FOR AVAILABILITY AND PURCHASE
EACH CALIPER $26.95 WITH USA SHIPPING (Handling Added Later)
BRAKE PAD SET FOR DISK BRAKE
$5.95
Plus Shipping and Handling
Brake pad set of 2. Mini-scooter/pocket bike disc brake pads,
set of 2. Commonly found on most stand-up scooters, tornado 43cc
and 2-stroke mid-pocket bikes. X-treme models. Specifications:
Length 28 mm, Height 18 mm, Thickness 5 mm
EMAIL SALES@SCOOTERSUPPORT.COM FOR AVAILABILITY AND PURCHASE
EACH REAR PAD SET $7.95 WITH USA SHIPPING (Handling Added Later)
BRAKE PAD SET FOR DISK BRAKE
$7.95
Plus Shipping and Handling
Square disc brake pads commonly found on 47/49cc pocket bikes
and pocket quads. Found on other vehicles as well. Some X-treme
models. Specifications: Length 39 mm, Height 27 mm, Thickness 6
mm. Fit the listed front brake above.
EMAIL SALES@SCOOTERSUPPORT.COM FOR AVAILABILITY AND PURCHASE
EACH BRAKE HANDLE $21.95 WITH USA SHIPPING (Handling Added Later)
6000z Wheel Bearings
(pair) $11.95
Plus Shipping and Handling
Two 6000z 1 1/32" diameter, 13/32" hole for a 3/8" Axle. FITS MANY
FRONT AND/OR REAR WHEELS OF SCOOTERS. Check the side of your
bearing for the number.
6001z Wheel Bearings (pair)
$15.95
Plus Shipping and Handling
Two 6001z bearings. FITS MANY FRONT AND/OR REAR WHEELS OF SCOOTERS.
Check the side of your bearing for the number. 1 3/32 inch
diameter, 15/32" hole for 15/32" diameter axle. X360 Bearings (a
15/32" O.D. sleeve, 1/16" wall, 3 7/8" long is used in the X360
version 1 wheels for a 3/8" diameter axle).
6200zz Wheel Bearings (pair) $15.95
plus shipping/handling
Two 6200zz 1.2" (1 3/16") diameter bearings, 2.5mm, 13/32" hole for
a 3/8" Axle. FITS MANY FRONT AND/OR REAR WHEELS OF SCOOTERS. Fits
the front wheel only on Vapor Scooter. The rear wheel of the Vapor
uses one 6200zz and one 6000z. Check the side of your bearing for
the number.
HW-11B Wheel
Bearings (pair) SOLD OUT
plus shipping/handling
1 1/8" diameter, with a thin flange 1.25" diameter, 1/2" Shaft
Two HW-11B diameter bearings
Often found for many 12 1/2" Wheels and axles, 1 1/8" diameter,
small flange 1.25" diameter, 1/2" Shaft
Vapor Scooter Rear Wheel Bearings (pair) $14.95
plus shipping/handling
A 6000z which is 1 1/32" diameter, 13/32" hole, and 6200zz which is
1.2" Diameter, 13/32" hole. For 3/8" Axle. The front wheel of the
Vapor uses two 6000z (see above). Check the side of your bearing
for the number.
Rear Wheel for X010 with Solid Tire
$34.95
plus shipping/handling
Rear Wheel with Solid Tire for most small 100 watt scooters. Belt
hub is 3M pitch for typical HTD3-384-12 or HTD3-447-12 size belts
of this pitch (small teeth) and width belt. 608z bearings and brake hub NOT included!
5/16 inch axle. Physical size: 5 1/2 X 1 Inch.
EMAIL SALES@SCOOTERSUPPORT.COM FOR AVAILABILITY AND PURCHASE
EACH WHEEL $39.95 WITH USA SHIPPING (Handling Added Later)
8" (200x50) RAZOR FRONT WHEEL with Tire $29.95
Plus Shipping and Handling
Razor front wheel for all scooters with 200x50 eight inch diameter
wheels. Includes 6200z bearings, rim, Scooter Tire and tube.
3/8" diameter axle available.
Actual dimensions: 7 5/8" diameter, 1 7/8 width. Add 1/4-1/2 inch
for valve stem clearance.
8" (200x50) REAR WHEEL FOR
MANY SCOOTERS $34.95
plus shipping/handling
Tire and tube, wheel rim, HTD 5M15 Pitch/belt width drive
sprocket. This is the original diminision rear wheel for almost all scooters including
Razor, Vapor, Escooter, Rad2Go, etc. 3/8" diameter axle. Includes bearings - 6000zz. Light weight
material Rim for kids use, Scooter Tire and tube, and 5M Pitch Belt Hub
is part of rim. 1 3/8 inch diameter screw threads on the other side for screw on brake hub
sold separately. Actual dimensions: 7 5/8" diameter, 3.5 width.
Brake hub inside lip is spaced 1/4 inch from side of rim. Rim at
bearing outside to rim at bearing outside measures 3.50 inches.
Belt side hub is flush with bearing. Spacers required to align belt hubs. 60mm brake assembly included. 2 pounds shipping weight.
70mm, 80mm, or 90mm Brake Hub and Drum available. PURCHASE 60MM BAND BRAKE ASSEMBLY
SEPARATELY PURCHASE 70MM BAND BRAKE ASSEMBLY
SEPARATELY OR PURCHASE 80MM BAND BRAKE ASSEMBLY AND HUB
SEPARATELY PURCHASE 3/8 REAR AXLE PURCHASE AXLE SPACER KIT
Front Rims for all scooters using 8 inch - 200 x 50
size tires. Bearing set included for 3/8 axle. Screws
Included. Metal or black composite material construction.
No Scooter Tire or tube included (order separately or order entire
wheel)
8" (200x50) RAZOR REAR WHEEL WITH SPROCKET, BRAKE, and TIRE $34.95
Plus Shipping and Handling
Actual measurements: 8 7/8" diameter, 2 3/8" width; 4 inch diameter
rim hole for total rim flange diameter of 5 inches, 4 Ply
non-marring reddish rubber Scooter Tire, 30 PSI. 90 degree valve
stem. 5/8" diameter axle that can be sleeved for different axle
diameters. Includes bearings, rim, non-marring reddish rubber
Scooter Tire and tube
2.50/2.80-4 OR 9" X 3.5"
FRONT WHEEL with Scooter Tire $47.95
plus shipping/handling
Pneumatic. Actual dimensions: 2.50/2.80-4 is 9 inch diameter with
2.75 width, 9X3.5 is 8 7/8 inch diameter, 3.25 inch width, 4 inch
diameter center for rim. Includes 6000z bearings for 3/8 inch axle,
silver rim, scooter Tire and tube. Front wheel
brake available. 6 pounds.
9 X 3.5" REAR WHEEL with
Scooter Tire and Sprocket $49.95
plus shipping/handling
Pneumatic. Actual dimensions: 10" diameter, 3.25" width
3/8" diameter axle size. Includes bearings, silver rim, scooter
Tire and tube. Front wheel brake
available. 7 pounds.
WHEEL, FRONT, 3.00-4 10 INCH or 9 X 3.5 INCH, WITH INSIDE DRUM
BRAKE - $49.95
plus shipping/handling
10 inch Front wheel with 3.00-4 Tire and tube
mounted on rim. Rim has 6000z bearings for 3/8 inch diameter axle.
Standard lever drum style brake fits this rim. Makes addition of
front brake possible with addition of lever and cable. 7/16 inch
spacer recommended between brake at axle and bearing, but not
required.
Includes #25/25H chain Drive Sprocket choice. Actual dimensions: 10" diameter, 3.25" width. Includes bearings, axle and adjusters, silver rim threaded for brake hub or rotor bracket on one side, sprocket with drive bearing attached on other side, and quality pneumatic tire and tube. As used on some Razor E300 and many X-treme Scooter models and other scooters universally. 55 tooth sprocket produces the most speed. 8 pounds. Order Drum Brakes and hubs above, if needed,Rotor available for disk use, Rotor Bracket available to attach rotor
9 X 3.5 OR 3.00-4 10" REAR WHEEL
and ROTOR BRACKET with Scooter Tire $49.95
plus shipping/handling
4 inch Aluminum rim for all scooters using 9 inch (2.50/2.80-4 and 9 x
3.5) or 10 inch (3.00 - 4) front tires. 2.5 inches wide. Includes bearings as used for 3/8 axle.
No Scooter Tire or tube included (order separately or order entire
wheel)
RIM, 9" or 10" FRONT WHEEL
$14.95
plus shipping/handling
General use 4 inch diameter steel rim with bearings for 5/8 inch axle. 2.25 inch from bearing to bearing outside, protrudes 7/8 out from edge of rim to bearing on one side, inset 7/8 inch from bearing to rim edge on the other side. These work fine with 9 or 10 inch tires and tubes, bent or straight stem.
No Scooter Tire or tube included (order separately or order entire
wheel)
RIM ONLY, 9" or 10" REAR TIRE FOR DRUM OR DISK USE $29.95
plus shipping/handling
Pocket bike rear wheel rim, for 110/50-6.5" Tube/Tubeless Tire and 90 degree valve stem, three spoke rim for 3 bolt disk rotor and 3 bolt sprocket attachment, 26 mm ID, Bent angle valve, Bolt hole spacing 33 mm, For racing purposes only not for highway use. Less 6000z Bearings and disk brake rotor and 3 hole #25H 47 tooth and 68 tooth sprockets available separately.
EACH 110/50 6.5" Rear RIM OUT WITH USA SHIPPING (Handling Added Later)
SEE TIRES & TUBES PAGE FOR 110/50-6.5 TUBELESS TIRE
RIM, 12.5" FRONT
WHEEL METAL $19.95
plus shipping/handling
Metal rim for all scooters using 12 inch - 12 1/2 inch wheels. 3 3/4
inches wide at axle. Uses 6001z Bearings (bearing set not included
- order separately if needed.
Four bolt Sprocket, Clutch bearing, and screw on brake hub not
included on rear rim - order separately.
8.5 inch Rim for 12.25 - 12 1/2 Tire/Tube - No Scooter Tire or tube included
(order separately or order entire wheel below). 3 pounds.
RIM, 12.5" REAR WHEEL METAL $27.95
plus shipping/handling
8.5 inch Metal rim for all scooters using 12 inch - 12 1/2 inch wheels. 3 3/4 inches wide at axle. Uses 6001z Bearings (bearing set not included
- order separately if needed.
Four bolt Sprocket, Clutch bearing, and screw on brake hub not
included on rear rim - order separately.
Rim for 12.25 - 12 1/2 Tire/Tube - No Scooter Tire or tube included
(order separately or order entire wheel below). 3 pounds.
RIM, 12.5" FRONT COMPOSITE BLACK
$9.95
plus shipping/handling
Nylon reinforced rim for all scooters using 12 inch - 12 1/2 inch
wheels. Uses HW-11B Bearings (bearing set not included - order separately if needed. 2 inches wide
at the axle. 8.5 inch Rim for 12.25 - 12 1/2 Tire/Tube - No Scooter Tire or tube included
(order separately or order entire wheel below)
12.5" BLACK FRONT WHEEL and
Scooter Tire With 5 Spoke Rim Complete $29.95
Plus Shipping/Handling
40-50 PSI max. Metal wheel with 3 spokes (straight or curved as available). For 15/32" diameter axle size. 3 3/4
inches wide at the axle. Includes 6001z bearings for 5.5" long axle
(15/32 inch diameter through bearings to 3/8 inch fork attachment, not included),
rim, scooter tire and tube. This wheel can also use a sleeve
inside the bearings to allow a 3/8 inch diameter axle use if necessary.
Picture may vary with the actual appearance of the wheel provided. We assemble each wheel prior to shipment as part of the handling fee.15/32" diameter
5.5 inch long axle available3/8" diameter
5.5 inch long axle available if shimmed
12.5" REAR WHEEL with
Scooter Tire $59.95 SALE - LIMITED QUANTITY
plus shipping/handling REG Price $89.95
55 tooth sprocket for #25 chain as equipped. Option for 65 or 80 tooth. 3 7/8" wide from
outside of brake hub to outside of sprocket. 1.5 inch from outside end of rim threads to spoke on each side. Includes free-wheel drive bearing with 4 hole sprocket attached, 3 spoke rim, 12 1/2"
Scooter Tire and tube, and 6200 axle bearings for 3/8 diameter
axles (order axle, brake hub, and brake drum above). 3/8"
diameter axle available.
EMAIL SALES@SCOOTERSUPPORT.COM FOR AVAILABILITY AND PURCHASE
EACH 12.5 REAR WHEEL $69.95 WITH USA SHIPPING (Handling Added Later)
Rim
Choice
OR,
SELECT AN EXCHANGE SPROCKET AT THE TIME OF THE ORDER:
EMAIL SALES@SCOOTERSUPPORT.COM FOR AVAILABILITY AND PURCHASE
EXCHANGE SPROCKET - $12.95 WITH USA ONLY SHIPPING INCLUDED
Thanks for shopping with us, we
appreciate your business.
SUMMARY:
When electric scooters first became popular our
Scooter Tubes (Innertubes), Tires (sizes: 12, 10, 8 1/2, 8, 200x50,
2.50-4, 3.00-4, 4.10/3.50-4), Airless (Airfree) Tires, Bearings
(including 6000z, 6001z, 6200zz), Wheels, Rims, Axles and wheel
hardware, and Common Scooter Tire Components were available for
customers in need who otherwise could not get parts for their model
scooters. Bearings for wheels and fork assemblies were hard to
find, and still are for quality parts. The difference in our
selection of tires, tubes, wheels, and parts from others' parts is
that we reject the cheap parts sometimes available to us. Plus, we
test the parts we sell prior to shipping them to our customers,
adding a little bit to the price but insuring quality. And with the
advent of Airless or Airfree tires that prevent freqent maintenance
we found a real timesaver for scooter owners. Bottom line - fast
receipt of quality airless tires, pneumatic tires and tubes, wheel
assemblies, bearings, axles and hardware, for almost all
scooters!
GENERAL INFORMATION common to most of the wheels we sell: Wheels consist of the Rim, Tire and Tube (or
Airless Airfree, if available) and may have attachments for the
brake and chain or belt sprocket. The Rim has wheel bearings of different sizes to fit, and for different axle diameters. Wheel rims come in different sizes appropriate for the tire
size used. To find the size of your wheel look on the side of the
tire or tube. All pneumatic tires and tubes are printed with the
Size which is often the Diameter and Width in either standard or
metric scale. If your tire says it is 200 X 50 in size then this is
the same as an 8" diameter by 2" width tire (25mm = 1 inch). The
inner tube and tire are also stated in the same size. Generally
the tire size is the approximate diameter and width (8 X 2 is 8
inch diameter by 2 inch width). Another way of stating size for a 10
inch diameter tire is 3.00-4 or 8 inch tire as 2.50-4 where the unstated diameter is
approximately 10 inches across with a tire width stated in the first
number and rim size diameter after the dash in inches. The wheel rim
diameter opening on the tire is approximately 4 inches.
HELP IN MAKING A SELECTION: We sell 8, 10, and 12 inch outside diameter wheels for general scooter use. To find the size of your wheel first look on the side of the tire for a tire size number to help possibly identify the rim diameter. All pneumatic
tires are printed with the entire tire Diameter and Width
information in either standard or metric size. Some sizing information (e.g., 110/50-6.5 6.5" rim) will also contain the rim diameter as the end number whereas many will not and are assumed to be common rims used in small scooters like 4 inch rims (200x50, 8.5x2, 9x3.5) or 8.5 inch rims for 12.5x1.75 to 12.5x3. We list our tires from the
smaller diameter and rim size at the top of this page, grouping them, and becoming larger in diameter
as you scroll down the page. Many scooters have a
wheel rim diameter of 4 inches and it may not be reflected in the
size. If your tire says it is 200 X 50 in metric size then this is
the same as an 8" diameter by 2" width tire (25mm = 1 inch) with a
4 inch diameter hole for the rim. The inner tube is also the same
size. A popular 3.00-4 ten inch diameter tire also has a 4 inch diameter
rim. 12 inch wheels have 8.5 inch rims. A 3.00-9 (or sometimes printed as 3.00 x 9) Tire size indicates the
width is 3 inches with a rim size of 9 in diameter. 3.00-10 Tire indicates a
width of 3 inches with a rim size of 10 in diameter. The rim size is the
size of the hole in the center of the tire, too. In some cases we list the
physical sizes of the tire or tube diameter in the tire, tube, or
wheel descriptions for your information and comparison, too. With
this comparative information you should not make a mistake in
ordering the correct size tire or rim. Some tires are listed with the Scooter brand
or make and model to also help your research. Finally, once the
size is determined you will need to select a front or rear rim that has the correct
attachments for the brake on one side and the sprocket on the other side, if used on the rear. Some front rims have brakes, too.
The brake may be either a band brake screw on hub, or a rotor that attaches
using a screw on rotor attachment bracket or the rotor bolts directly to the rim.
The sprocket usually has a screw on drive bearing that the sprocket bolts to.
Rims will project these attachment points on both sides at different distances
from the center of the rim and this aligns the chain and brake components in
order to work properly. There are front rims and rear rims made for the
components that attach to them. The axle diameter for the bearings used in
the rims may be 3/8, 15/32, or even larger. Axles may have varying diameters
in the same axle at different points, too. It is easily possible to assemble
a wheel using all the listed components purchased separately, but we offer
many wheels complete, plus OEM versions are available for Razor and X-treme
Scooter models on this website. We do not have details on the OEM rims and wheels. EMAIL US IF YOU ARE IN DOUBT BEFORE YOU ORDER!
SEE OUR TERMS OF SALE, ORDER POLICIES, TO UNDERSTAND HOW TO EXCHANGE OR IF NECESSARY RETURN SOMETHING YOU ORDERED IN ERROR!! LINK IN THE LEFT COLUMN.
NOTICE: PICTURES OF REPLACEMENT PARTS MAY VARY PRIOR TO UPDATES. PARTS ARE PROVIDED IN AS-IS CONDITION WITH NO REGARD TO SLIGHT COSMETIC IMPERFECTIONS DUE TO STORAGE OR HANDLING, AND PRODUCTION RUNS MAY SLIGHTLY ALTER THE APPEARANCE OF THE SAME PART FROM TIME TO TIME MAKING SLIGHT DIFFERENCES FOR MATCHING OF SEVERAL ITEMS IN AN ORDER (WHENEVER POSSIBLE WE MATCH AS CLOSELY AS POSSIBLE FOR ORDERS WHERE CUSTOMERS REQUEST THIS). ALL PARTS ARE INSPECTED AND TESTED AS POSSIBLE FOR QUALITY CONTROL PRIOR TO PACKAGING AND SHIPMENT OF CUSTOMER ORDERS. ALL SALES ARE FINAL WITH THE EXCEPTION OF NON-ELECTRICAL ITEM EXCHANGES FOLLOWING OUR TERMS OF SALE ORDER POLICIES FOR THE ORDERING OF INCORRECT PARTS. CUSTOMERS SHOULD ALWAYS TAKE ADVANTAGE OF OUR 24/7 EMAIL AND OTHER COMMUNCIATIONS FOR HELP PRIOR TO PLACING ORDERS, IF NEEDED. USA STANDARD SHIPPING IS INCLUDED IN THE PRICE OF PARTS ONCE ADDED TO THE SHOPPING CART THAT ALSO REPRESENTS THE HANDLING FEE FOR INTERNATIONAL ORDERS. INTERNATIONAL SHIPPING IS SEPARATE FOR EACH ORDER BASED ON INFORMATION PROVIDED ON OUR 'HOW TO PLACE AN ORDER' PAGE USING THE LINK IN THE ITEM DESCRIPTION. USA HANDLING IS ADDED TO EACH ORDER DURING CHECK-OUT TO ADJUST SHIPPING AND PROCESSING OF EACH USA ORDER. PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE AND CUSTOMER WILL BE ADVISED IN THAT EVENT.